Completing a computer takes many steps installation, from the steps to manually install the CPU for the computer to RAM or VGA and other ingredients. It seems that these stages are very complicated and steps to install a PC for you is not possible. But please do not think so if you finish this article of our guide steps to install CPU manually for the computer, steps to install a PC.
If you can’t afford to buy a new computer and install it yourself. Why not use your old computers, the ones that you need to clean up for practice in this article. However, ElectrodealPro also advises readers to consider carefully when performing this procedure.
Steps to manually install a CPU for a computer, steps to install a PC
The components to install in this article:
– Computer shell – Main – Motherboard
– Chip – CPU of the computer
– RAM – Internal memory
– HDD – Hard drive
– VGA – Video card
– Computer power
– Radiator fan
– Block main
– Cape Sata cord, power cord.
– 4-sided screwdriver.
– Glue heat dissipation
Perform the steps to manually install the CPU for the computer, steps to install the PC
Step 1: First we proceed to remove the basket so we can mount the computer’s parts. At the back of the chassis there is a total of 4 screws that are easy to screw by hand, then tug on the side of the chassis to reveal the inside of the body.
Step 2: Usually the current models are powered at the bottom, in addition we can see the location in proportion to the source on the machine and install it, proceed with screws when the source is fixed.
Step 3: Next, install Block for the main, fixed components and only compatible with the Main type to help protect the Main from external influences. Look at the chassis you will immediately see the corresponding position of this component.
Step 4: After installing the power, you pull all the cables, the power of the machine and other components to post later to increase the aesthetics.
Step 5: The steps to manually install the CPU for the computer are as follows: Put the Main latch bar up, remove the chip protector of the main, this step you really do be careful because it can cause the main leg.
Step 6: Proceed to install the chip, match the 2 sides of the chip corresponding to the Main position and install it.
Step 7: slowly put on the Main in accordance with the identified positions in the above step to avoid being channeled, very easy to damage the Main leg.
Step 8: Then close the Main handle bar as drafted.
Step 9: On the side of the chip is the RAM, you pull the 2 ends of RAM to the sides then compare the slot of RAM with Main and plug straight down.
After plugging in, close the latch.
Step 10: Fix Main into the computer case, you can see up to 9 places you need to screw.
Step 11: To fix the Main, you just need to find the Block for Main and install it accordingly, in addition there are holes to help you screw in.
Step 12: Proceed to power supply for Main through pin 20 PIN on main and source.
Step 13: Install the post block behind the Main to fix the VGA in the front if you use a removable heatsink, but if it is a regular heatsink, you just need to screw in to finish.
Step 14: In the previous post, you put glue on the chip and the heatsink fan and then put in 4 corresponding places to screw on the Main
Screw back to ensure the heat dissipation works properly.
Step 15: Install the audio signal wire under Main, next to the source, locate and plug in.
Step 16: Carefully refer to the following diagram to correctly insert the power cord, turn off, Restart the machine to let the buttons on the Case work. Fortunately you can plug it in to try it out without harming the Main.
Step 17: Different types of Mains will have different arrangements, but the most important thing is that the two Power features – turn off, turn on the machine and Restart – restart the computer to work.
Step 18: Proceed to install the hard drive into the tray available in the chassis, insert the screw to reposition the hard drive.
Step 19: Then insert the power cord from the machine’s power into the hard drive, standard Sata.
Step 20: The next step in the PC installation steps is to use a standard Sata cable connected from the Main to the HDD.
Step 21: Plug it directly into the HDD, rotate to the correct direction to plug.
Step 22: In the VGA mounting part, you proceed to install the latch bars for the case, these bars fix the VGA as well as avoid dust entering the machine.
Step 23: To horizontal VGA and then plug directly into the PCIx16 slot, note that you need to see the VGA pin before plugging it in.
Then fix it with screws to prevent VGA too heavy to break the plug.
Step 24: Carry out auxiliary power to the high-end VGA, the GA needs many sources.
Done this step, you just plug in and install it, the steps to manually install the CPU for the computer as well as the steps to install the PC have been completed. You have installed a computer with the most important components.
Above, ElectrodealPro has finished guiding you steps to self-install CPU for the computer, steps to install a PC. After this stage is steps to install a computer, use. You should also do a little research before doing it.