Instructions to fix "Network path was not found" in Windows
Random Tech News

Instructions to fix “Network path was not found” in Windows

When a computer, mobile device, or printer tries to connect over a network to a Microsoft Windows computer for example, an “network path was not found” error message – Error 0x80070035 may appear. The computer cannot make a network connection with the other device.

This error message is usually displayed: The Network Path Cannot Be Found.

Error message image The network path was not found would look like this:

Network error message was not found

Any technical problems online can cause this error. Try the troubleshooting methods listed here to resolve or fix this problem.

Instructions to fix error 0x80070035 Windows

Method 1: Use a valid path name when encountering Cannot Be Found Network Path error

Error 0x80070035 can occur when a user enters an incorrect network path name. The specified path must point to a valid shared resource on the remote device. The Windows file or printer sharing feature must be enabled on the remote device and remote users must have access to the resources.

Method 2. Other causes of error

Any abnormalities in the system, including the Cannot Be Found Network Path error, can occur when clocks on two devices are not set to the same. Keep Windows devices on the local network synchronized through the Network Time Protocol. This can avoid the Network Path Cannot Be Found error.

Make sure to use the correct username and password correctly when connecting to remote resources.

If any of the Microsoft system services related to file sharing and printer sharing on the network fail, the Network Path Cannot Be Found error may also occur.

Restarting the computer can restore normal functions.

Method 3: Disable the local firewall

A misconfigured firewall or running improperly on the initialized Windows device can cause Cannot Be Found Network Path. Temporarily disable the firewall, built-in Windows firewall, or third-party firewall software, then check to see if the Network Path Cannot Be Found error still occurs.

If the error no longer appears, users should take additional steps to change the firewall settings to avoid reactivating the error. Note that home desktops are already protected by broadband router firewalls, so there is no need to install their own firewall, and mobile devices need a separate firewall to protect them.

Method 4: Reset TCP / IP

The average user doesn’t care much about technical issues related to operating system operation, but others want to learn advanced troubleshooting options. A common method for working with a more stable Windows network is to reset the components of Windows running in the background that support TCP / IP network traffic.

The specific steps involved will depend on the version of Windows you are using. However, this approach usually involves opening the Command Prompt on Windows and entering the “netsh” command. For example, the command:

netsh int ip reset

This command will reset TCP / IP on Windows 8 and Windows 8.1. Restarting the computer after executing this command will return Windows to its default state.

Method 5:

We press the key combination Windows + R to open the Run dialog box and enter Keyword NCPA.CP. Then press Right-click on the network that is accessing then select Properties.

Enter the keyword NCPA.CPL

Display the new user interface Internet Protocol Version 4 (TCP / IPv4) in the list below and then click next Properties.

Internet Protocol Version 4 (TCP / IPv4)

Switch to the new dialog box you click Advanced, then select WINS tab, tick on it Enable NetBIOS over TCP / IP and click OK to save it.

Activate NetBIOS

Method 6:

We access the Windows Services interface on the computer, then check serivces TCP / IP NetBios Helper is already active or not. If not, then click directly on serives and then switch to operating mode.

Activate services

Method 7:

We enter gpedit.msc keyword into the Run dialog box to access the Local Group Policy Editor. Next, click on the user Computer Configuration, choose Window Settings on the right, select next Security Settings.

Computer Configuration

Next click Local Policies then click continue Security Options then look to the right to find it lock Account: Limit local acc use of blank password to …

Find the Account key: Limit local acc use of blank password ...

We will move on Disable by double clicking on this key. Press Apply to save.

Turn off the lock

Next you find next Network access key: Sharing and security model for local account to switch on Classic.

Back to the computer interface we open Run dialog box then enter Keyword cmd. Next to the user to enter gpupdate / force command to update gpedit again.

Switch to Classic mode

Method 8:

Users also access Local Group Policy Editor, then follow the link Computer Configuration> Windows Settings> Security Settings> Local policies> Securiy Options.

Security Options

Next we find next Network security key: LAN Manager Authentication level then move on Send LM & NTLM -user NTLMv2 senssion security if negotiated. Press Apply to save.

Finally open Run dialog box then enter cmd, import gpupdate / force command to update gpedit again.

Network security: LAN Manager Authentication level

Method 9:

We will proceed to verify whether the drive is shared or not, by right clicking folder to share then select Properies. Click on it Sharing tab then check if the folder is shared. If not, press Share button to share.

Share a folder

Then we choose who we want to share and then grant that person permission.

Select shared account

Method 10:

We need Verify the connected computer’s IP address because it is possible that the network address is not properly connected.

We press Windows + R to Open the Run dialog box in the destination computer and then type cmd command. In the command input interface Click ipconfig / all. Display the parameters and you need to pay attention to the IPv4 parameters.

IP address

In shared computer we too Enter cmd in the Run dialog box, later Enter the ping command of the destination computer then press Enter.

The result shown will give you the 4 following information to indicate that you have linked.

Enter the test order

Or we can visit Troubleshoot in Windows Settings, then click Network Adapter Troubleshooter to run the connection error checker.

Check network connection

Method 11:

In the interface Run dialog box you enter keyword devmgmt.msc. Then we find the section Network adapers then click on each driver and then select Update driver.

Update network driver

So you have a lot of ways to fix, check the computer when unable to connect computers in the LAN, with Network Path Cannot Be Found error.

Hope this article was helpful to you!

See more:

  • Fix “A Duplicate Name Exists On the Network” error
  • “Connected With Limited Access” error in Windows
  • Instructions to fix error A network cable is unplugged in Windows


Leave a Reply

Your email address will not be published. Required fields are marked *